Service, brakes

BMW

Item No.: 10159989

Manufacturer No.: 34118054826

The following parts are also essential: brake pads, brake pad sensor and brake pad paste.

BMW

Item No.: 10159988

Manufacturer No.: 34118054825

The following parts are also essential: brake pads, brake pad sensor and brake pad paste.

BMW

Item No.: 10158528

Manufacturer No.: 34108064560

BMW

Item No.: 10158546

Manufacturer No.: 34108094045

TX4007

BMW

Item No.: 10158529

Manufacturer No.: 34108064561

BMW

Item No.: 10158530

Manufacturer No.: 34108064562

BMW

Item No.: 10164890

Manufacturer No.: 34356870351

BMW

Item No.: 10159718

Manufacturer No.: 34116872573

BMW

Item No.: 10159717

Manufacturer No.: 34116872572

BMW

Item No.: 10159990

Manufacturer No.: 34118054827

370X24

BMW

Item No.: 10159991

Manufacturer No.: 34118054828

370X24

BMW

Item No.: 10017415

Manufacturer No.: 34212284466

The S4007 or TX4007 brake pad (new product designation from F90 vehicles) is derived from a proven endurance racing pad used in motorsport. It has been specially developed for increased thermal performance and meets the requirements of ECE-R 13H (legal requirement in many countries). The following significantly different properties compared to the standard brake pad must be observed: The design of the brake force distribution is racing-oriented. This supports dynamic steering on the brakes and differs significantly from the standard configuration. Increased stress on the brake discs: Due to the modified friction mechanisms, the brake disk wears faster. It is therefore recommended that the brake disc is also replaced when this brake pad is fitted. It is essential to replace the brake disk if there are cracks of 13 mm or more, even before the brake pad wears out. -shorter braking distance -better brake response -higher thermal load capacity Safety instructions: Installation only in conjunction with new brake disks (the brake disks of M vehicles are all perforated)! Due to its special properties, the pad reacts even more sensitively to external influences such as rim cleaner, road salt and parking the vehicle with a wet brake disk. Therefore, operation in winter is not recommended. Direct spraying of the brake pad and disc with rim cleaner should also be avoided.

BMW

Item No.: 10160368

Manufacturer No.: 34208093728

BMW

Item No.: 10164896

Manufacturer No.: 34356880543

BMW

Item No.: 10164889

Manufacturer No.: 34356870350

BMW

Item No.: 10158758

Manufacturer No.: 34111123072

M8X12

BMW

Item No.: 10158378

Manufacturer No.: 34106864424

M12X1,5X43 ZNS3

BMW

Item No.: 10158378

Manufacturer No.: 34106864424

M12X1,5X43 ZNS3

BMW

Item No.: 10412450

Manufacturer No.: 83192180000

3 g

BMW

Item No.: 10412445

Manufacturer No.: 83192158851

To eliminate brake noise. Prevents seizure and corrosion. Facilitates assembly and disassembly. High-quality mineral grease with solid content. Very long-lasting and high lubricating performance -Service and repair product

BMW

Item No.: 10412488

Manufacturer No.: 83192362037

Safety cleaner for brake parts cleaning and for various maintenance, repair and assembly work. Reduced health risk as n-hexane free. Removes dust, incrustations, oil, grease, resin, silicone and anti-corrosion coatings. Very good cleaning performance with minimal fire risk. Tested fire behavior, no afterburning, no flashback, lower explosion limit >1.5 vol %. Conservation of resources through the use of renewable raw materials. Application: -Maintenance and repair -Clutch repairs -Degreasing of all assembly parts -For heavily soiled or oily/greasy parts -Safety cleaner 2.0 for maintenance, repair and assembly work -reduced health risk as n-hexane-free* -Conserves resources through the use of renewable raw materials Removes dust, incrustations, oil, grease, resin and anti-corrosion coatings -reduced risk of fire and fire consequences -formulation independently tested by TÜV Süd -state-of-the-art cleaning technology -Lowest hazard potential -Recommended product in accordance with the Hazardous Substances Ordinance (protection level 2) The surfaces to be treated must be mechanically cleaned of coarse dirt and sufficiently sprayed until the surface is clean and shiny. The treatment may need to be repeated in the event of heavy soiling.